Batch mixing nozzle optimizes production of the treatment that note model

  • Time:
  • Click:94
  • source:AYOR CNC Machining
Batch mixing nozzle -- well-known, lubricious grain is the problem that the treatment that note model appears extremely easily, use static batch mixer, namely batch mixing nozzle, can avoid the happening of this kinds of problem effectively. And little-known is, besides rise stability and reduce manufacturing cost, batch mixing nozzle still can solve problem of a lot of and other character. In the past a few years, the screw structure of the equipment that note model and electronic control already were experienced classics is improved, ensure thereby already efficient finish model quickly to change again and of lubricious mother bead and other additive mix. But because note model,be discontinuous process, in different time paragraph inside, fuse-element still is met keep in makings canister. To come true as far as possible quick fuse-element treatment, need high temperature of have the aid of from exterior heat makings canister. Two kinds of afore-mentioned methods can cause fuse-element to be mixed in its cross section difference in temperature appears in the stroke that note model, can cause the difference of viscosity and rate of going from place to place subsequently. The land that there was use force in nozzle of the batch mixing below this kind of circumstance (see a picture 1) . Go to static blender conformity the nozzle that note model, can assure the homogenize in the temperature in the whole cycle that note model, viscosity and rate of going from place to place (see a picture 2) . A lot of quality problems that appear in the production that note model are immediate the difference change with temperature, viscosity and rate of going from place to place is relevant. Distributing through optimizing temperature and rate of going from place to place, can narrow significantly dimension deviation, avoid exterior flaw, be like scotoma and window. The defect of this respect is caused by flow mark, use afore-mentioned methods can great the happening that reduces blemish, the pen core that shows like example place plays a slideway (see a picture 3) . The fact proves strongly, nozzle of use batch mixing (manufacturer: Switzerland limited company of solution of Promix of Wen Tetu Er) , can avoid afore-mentioned flaw effectively, promote component the intensity in this bits. Cost of bead of mother of Nextpage managing color and promotion can blender of effect static state already was approbated extensively, it can promote batch mixing the standard, avoid the occurrence of lubricious grain issue effectively. Batch mixing spray head is used when producing cap, the lubricious grain amount that can reduce infuse dot to appear significantly really (see a picture 4) , already obtained at this o'clock in practice confirm. Answer the question in production, the dominant position of static blender is more than still and such, its capacious treatment uses a space, make its can optimize the craft that note model further, and be below very much circumstance can reduce manufacturing cost considerably. More and more treatment facilities transform nowadays expect to use lubricious mother or liquid colorant is direct and chromatic, thereby cost of managing raw material, make production more stretch and flexible. However, because machine a condition for example the influence of temperature, back pressure and screw speed to color depth, and machine the stability that the process must assure colorant is metric agree, use the constant of character of direct lubricious unwarrantable color treatment consequently. Lubricious mother bead the union of gage and batch mixing nozzle, can make the effective solution of this kind of problem. Batch mixing nozzle can assure completely consistent chromatic quality, and the type that need not consider to fix model equipment and its operation pattern. This craft but dye of color of efficient break up reunites content, make its all distributing character, according to specific colorant and requirement different, but additional the use amount that reduces mother makings and liquid colorant amounts to 15-25% . Through undertaking to spare parts and material more balanced temperature is controlled, fuse-element temperature often can reduce 10 ℃ . This advantage promoted the sources of energy efficiency greatly, additional shorten cooling time, and cooling time often decided when to producing cycle, grow below a lot of circumstances. A lead company has used this craft to drop fuse-element temperature, in 2.

5kgIn the production of PP container, when will producing cycle, can grow to shorten from 120s to 100s. Blender of static state of mixture screw VS falls in some circumstances, increase back pressure and amount of lubricious mother bead to be able to alleviate lubricious grain issue, but this method can bring cost of higher lubricious mother bead, and the influence as a result of polymer type, can bring about model to spend the service loss of life of screw, not disappear says, of the advisability that this is not economy anthology. Mixture screw does insoluble color mix an issue? Although the answer is of active affirmation, but as proper as configuration static state blender is compared, mixture screw still is put in quite big drawback. Through adjusting screw speed and back pressure, mixture character promotes somewhat really. But colour reunites content is in mixture screw can break up arrives finite degree, because,this is, although be in a certain bit more specific shearing force is very tall, distributing not even however, compare efficiency because of this and static blender inferior. More than and such, screw mixes area to often can reduce model to change the length of area, and the main function that latter just is screw. This bit is very important also finally, replace standard model to turn screw than coming with mixture screw, install batch mixing spray head and blender of integrated static state is more convenient and quick, and cost is lower. Oneself of blender of Dan Jing condition also is put in certain limitation, what can compensate color depth inside finite degree only is metric not all. And for love or money, adoption blender must undertake essence of life allows to adjust according to the specific utility of the requirement. The measure that influencing factor includes to fix model equipment not only and force combining a model, still involve shape goods and adoption plastic capable person are qualitative. Configuration installs undeserved static blender, or can solve partial problem only, flat whats do not solve or. And afore-mentioned mistakes, increase what can cause pressure loss significantly, bring about polymer to decompose. The additional pressure loss that the place of batch mixing nozzle that installs correctly causes won't exceed the 10-15% of infuse model pressure. The geometrical appearance of blender also can affect treatment result, and blender assures to undertake in whole cross section high speed runs on very short installation length only, treatment just is met as a result satisfactory. Below a lot of circumstances, the blender structure that does not match or improper configuration installation can bring about unqualified treatment, and such treatment error often can be ascribed to the functional sex problem of static blender technology. The crucial level in applying actually is the smallest pressure loss and efficient ego cleanness. Convenient ego cleanness and blender of material character static state often are thought to pile up easily material precipitates and hard complete cleanness, such misapprehensive long-standing. And fact rather, because blender writtens guarantee construction is become,some problems are, because the installation of outer garment deviation or outer garment joins means is caused,another some is. Static blender need not disassemble but complete cleanness. Below good position, blender can use redundant polymer to undertake online purify cleanness. A cleanness that records here experiments, use spray head of Promix batch mixing, test result shows, the 3 times clean fuse-element at blender bulk is measured enough and complete clean blender (see a picture 5) . This amount spends the use amount of screw under clean empty conduit or model far. In the treatment that note model, the mechanical load that static blender shoulders is tremendous. Registering model level, blender must bear continuously the alternant bear that is as high as hundreds of Bar, this or planning in material, structure and configuration is perfect and harmonious circumstance below. Accordingly, rigorous, persistent quality assures crucial. Below the case that uses high quality blender and correct distribution program, accurate operation to move, need not additional preparation fittings. The fact proves, even if machines caustic filler, what the service life of blender still grows several years is long. Solution of blender of overview static state can promote the stable reliability of the treatment that note model, reduce lubricious mother bead to use an amount, optimize the craft that note model from whole. Issue of quality of a lot of product can get here simple and easy and convenient and of economy solve. Only requirement is a basis merely specific applying and undertake choice of structure of correct and sound distribution program, blender and batch mixing nozzle are configured just. CNC Milling